798646e1

14.4. Alarm and lighting fixtures

Service of head headlights

Removal and installation

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. On Utiliti's (Van) models (Utility) and Cab Chassis release fixing clamps and remove a front grille from the car.
  3. Disconnect an electrical wiring from the headlight block.
  4. Supporting a block headlight, give screws of fastening of a ring of her holder. Remove a ring of the holder and a block headlight from the car.

Try not to change in the course of performing procedures of removal and installation of a head headlight casually situation е adjusting screws.

Installation is made upside-down.

Replacement of a lamp of a head block headlight of semi-tight type

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Disunite the electric socket of a head headlight.
  3. Remove a rubber protective cover from a back part of a block headlight, press on the holder of a lamp and turn it counterclockwise. Take a lamp from a block headlight (components of a block headlight are shown on an accompanying illustration).
1 — a protective cover
2 — the holder
3 — a lamp
4 — a block headlight
5 — a ring
6 — screws

Try not to touch a glass flask of a lamp with naked fingers. Fatty deposits reduce lamp service life. Incidentally left spots can be removed with use of methyl alcohol then the flask should be dried up, having wiped it with a pure napkin or a piece of cotton fabric.

  1. Establish a new lamp in a cartridge. Check correctness of its installation. Also check correctness of installation of the holder and a protective cover.

Adjustment

 PERFORMANCE ORDER

  1. Make sure of correctness of pressure of a rating of tires and completeness of gas station of the fuel tank. Park the unloaded car on the flat horizontal platform. On a driver's seat put the assistant.
  2. In the presence of the special device for adjustment of the direction of beams of head headlights attentively study the enclosed instruction.
  3. When using a control board the car should be parked in five meters from it (distance And on an illustration - see below) and perpendicular to the board plane.

As a control board the flat wall on which it is necessary to apply with chalk the corresponding marking can be used.

  1. Chalk draw on a board the horizontal line of a marking passing through the axial plane of head headlights of the car and at height of their centers (see an accompanying illustration).
1 — the central lines
2 — a control board
3 — the car
4 — a spot of driving beam
5 — a spot of passing beam
6 — the correct arrangement of light spots
  1. Draw two vertical lines corresponding to vertical central lines of head headlights of the car.
  2. Turn on passing beam of head headlights.
  1. Screw against the stop the adjusting screws located above and on each side block headlights (see an accompanying illustration), then release them, trying to obtain the required direction of beams of headlights.
  1. Adjust the direction of beams of head headlights according to requirements of traffic regulations accepted in the concrete region. Generally achieve such placement of spots of passing beam when the line of a horizontal cut of a spot is on the horizontal line of a marking on a board, or slightly below it. The lifted part of a spot has to appear on the vertical line of a marking, or slightly more to the right of it.

Service of the forward combined lamps

On Utiliti's (Van) models and the Mini-truck of late years of release the forward combined lamps of the same design, as on models Hardtop and the Versatile person are established (procedures of service are completely similar described below).

Replacement of lamps of parking fires

All models, except Utiliti (Van) and the Mini-truck

 PERFORMANCE ORDER

  1. Give fixing screws and remove assembly of the combined lamp.
  1. Turn a cartridge counterclockwise and take it from assembly of a lamp (removal of a lamp of forward parking fire of cars of models Hardtop and the Versatile person is shown on an accompanying illustration).
  1. Having grasped a flask, carefully pull a lamp, taking it from the boss.
  2. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  3. Install assembly of the combined lamp on the car.

Utiliti's (Van) models and Mini-truck

 PERFORMANCE ORDER

  1. Give fixing screws and remove a lens of the combined lamp with a sealant.
  2. Press a lamp, turn it counterclockwise and take from the boss.
  3. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  4. Establish into place a lamp lens, having tracked for installations of a rubber sealant.

Replacement of lamps of indexes of turns

All models, except Utiliti (Van) and the Mini-truck

 PERFORMANCE ORDER

  1. Give fixing screws and remove assembly of the combined lamp.
  1. Turn a cartridge counterclockwise and take it from assembly of a lamp (removal of a lamp of the forward index of turn of cars of models Hardtop and the Versatile person is shown on an accompanying illustration).
  1. Press a lamp, turn it counterclockwise and take from the boss.
  2. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  3. Install assembly of the combined lamp on the car.

Utiliti's (Van) models and Mini-truck

 PERFORMANCE ORDER

  1. Give fixing screws and remove a lens of the combined lamp with a sealant.
  2. Press a lamp, turn it counterclockwise and take from the boss.
  3. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  4. Establish into place a lamp lens, having tracked for installations of a rubber sealant.

Replacement of lamps of separately established indexes of turns (model of late years of release)

#252525

 PERFORMANCE ORDER

Installation is made upside-down.

  1. Previously check a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  2. Install assembly of the index on the car.

Replacement of lamps of indexes of turns of models of Utiliti (Van) and Mini-truck

 PERFORMANCE ORDER

  1. Give fixing screws and remove a lens with a sealant.
  2. Press a lamp, turn it counterclockwise and take from the boss.
  3. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  4. Establish into place a lamp lens, having tracked for installations of a rubber sealant.

Service of the back combined lamps

All models, except Utiliti (Van) and the Mini-truck)

 PERFORMANCE ORDER

  1. Give fixing screws and remove assembly of a lamp of the car.
  1. Turn a cartridge counterclockwise and take it from assembly of a lamp (removal of one of lamps of the back combined lamp of cars of models Hardtop and the Versatile person is shown on an accompanying illustration).
  1. Press a lamp, turn it counterclockwise and take from the boss.
  2. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  3. Install assembly of the combined lamp on the car.

Utiliti's (Van) models and Mini-truck

 PERFORMANCE ORDER

  1. Give krkpezhny screws and remove a lens of the combined lamp with a sealant.
  2. Press a lamp, turn it counterclockwise and take from the boss.
  3. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  4. Establish into place a lamp lens, having tracked for installations of a rubber sealant.

Utiliti's (Van) models and Mini-truck of late years of release

 PERFORMANCE ORDER

  1. Give fixing screws and remove assembly of a lamp of the car.
  1. Press a lamp, turn it counterclockwise and take from the boss (see an accompanying illustration).
  1. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  2. Install assembly of the combined lamp on the car.

Replacement of lamps of fires of a backing of models Hardtop and Versatile person of late years of release

 PERFORMANCE ORDER

  1. Give fixing screws and remove assembly of a lamp of the car.
  1. Press a lamp, turn it counterclockwise and take from the boss (see an accompanying illustration).
  1. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  2. Install assembly of the combined lamp on the car.

Replacement of lamps of stoplights of the top level (model of late years of release)

 PERFORMANCE ORDER

  1. By means of the screw-driver remove a finishing slip from assembly of a stoplight.
  2. Turn a cartridge of a lamp counterclockwise and take it from a lens.
  3. Having pulled, take a lamp from the boss.
  4. Make sure of lack of corrosion of the boss and insert into it a new lamp.
  5. Establish a cartridge with a lamp in a lens. Turn a cartridge clockwise for fixing it in a lens.
  6. Establish a finishing overlay for the assembly basis. Screw and reliably tighten the fixing screw.

Replacement of a lamp of illumination of registration plate

 PERFORMANCE ORDER

  1. Give fixing screws and remove a lamp lens together with a sealant.
  1. Press a lamp, turn it counterclockwise and take from the boss (see an accompanying illustration - the lamp of models Hardtop and the Versatile person is shown).
  1. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion, and a lamp on compliance to nominal requirements for power and supply voltage (see size tables and adjustments at the end of the Management).
  2. Install assembly of the combined lamp on the car.

Replacement of the lighting lamp of salon when opening doors

Utiliti's (Van) models and Mini-truck

 PERFORMANCE ORDER

  1. Having hooked the small screw-driver, carefully remove a plafond from the lamp case.
  2. Having grasped a flask, carefully pull a lamp, taking it from the boss.
  3. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion. Make sure of reliability of fastening of the lamp guaranteeing quality of electric contact.
  4. Establish into place a lamp plafond.

All models, except Utiliti (Van) and the Mini-truck

 PERFORMANCE ORDER

  1. On the models equipped with the lamp of square shape carefully having hooked the small screw-driver, remove a plafond from the lamp case.
  2. On models with the round lamp for removal turn a plafond counterclockwise.
  1. Carefully take a lamp of scalloped type from terminal clips of the holder (see an accompanying illustration).
  1. Establish a lamp in a cartridge, previously having checked a cartridge for existence of traces of corrosion. Make sure of reliability of fastening of a lamp in clips of the holder guaranteeing quality of electric contact.
  2. Establish into place a lamp plafond.

Replacement of a mate lamp (model of late years of release)

 PERFORMANCE ORDER

  1. Having carefully hooked the screw-driver, remove a plafond from assembly of the lamp.
  1. Press a lamp, turn it counterclockwise and take it from the boss (see an accompanying illustration).
  1. Installation is made upside-down. Check a cartridge for lack of corrosion and establish the new lamp corresponding removed in working parameters (see size tables and adjustments at the end of the Management).
  2. Establish into place a plafond.