Nissan:: Patrol:: Appendices

14:14. Appendices

Nominal force of tightening of threaded connections is specified in the end of each of Sections of the Appendix, and also included in composition of material of paragraphs of the text of the Management.

General technical characteristics

Characteristic

Value

Full length, mm

Station Wagon

4810

Versatile person

Ti 4890

Hardtop

4240

To the utility (Van) (Utility) and Cab Chassis 4970

To the utility (Van) and the Mini-truck of late years of release (since 1992) with a suspension bracket on screw springs

4700

Full width, mm

The versatile person and Hardtop (without slips on wings)

1800

The versatile person and Hardtop (with slips on wings)

1930

To the utility (Van) and Mini-truck

1690

To the utility (Van) and the Mini-truck of late years of release (since 1992) with a suspension bracket on screw springs

1930

Wheel base, mm

Versatile person, Utiliti (Van) and Mini-truck

2970

Hardtop

2400

Radius of turn, m

Versatile person, Utiliti (Van) and Mini-truck

6.7

Hardtop

5.5

Volume of the fuel tank, l

Versatile person and Hardtop

95

To the utility (Van) and Mini-truck 90

The admissible mass of the towed trailer, kg

Models of early years of release (till 1992)

The trailer equipped with brakes

2500

The trailer which is not equipped with brakes

750

Models of late years of release (since 1992)

The trailer equipped with brakes

The versatile person with RKPP

2800

All others

2500

The trailer which is not equipped with brakes

750

Maximum corner of a forward sves

42 °

Maximum corner of a back sves

30 °

Maximum corner of a platform
31 °

Maximum road gleam, mm
235

Maximum admissible depth of a water barrier, mm
600

Types and volumes of lubricants and liquids

All volumes are specified only approximately. Exact data can be obtained according to indications of measuring probes or definition through control/jellied openings.

Engine

Characteristic

Value

Type of the greasing liquid
SAE 20W/50SE is not worse than quality

Volume of the pallet of a case, l

Engine of 4.2 l

With the filter

8.2

Without filter

7.7

Engine of 3.0 l

With the filter

6.4

Without filter

6.0

Cooling system

Characteristic

Value

The volume of cooling liquid (including a broad tank), l

Models of 3.0 l

11.9

Models of 4.2 l with RKPP

13.9

Models of 4.2 l with AT

13.6

Antifreeze type
Antifreeze on the basis of ethylene glycol

Composition of mix, % content of antifreeze

To - 15 °C

30

To - 35 °C

50

Manual transmission

Characteristic

Value

Type of the greasing liquid

SAE 75W/90 GL4

Volume, l

Engine of 4.2 l

3.9

Engine of 3.0 l

3.6

Engines of 3.0 l of models of release since October, 1994.

5.1

Automatic transmission

Characteristic

Value

ATF type

Matic D

Volume, l

Early models

8.5

Models of late years of release (since 1992)

11.8

ATF Matic D is the Australian equivalent of the Japanese ATF Dexron II. Use of the Australian liquid with the name Dexron II can lead to a transmission exit out of operation.

Transfer case

Characteristic

Value

Type of the greasing liquid

Models of early years of release (till 1992)

SAE 75W/90 GL4

Models of late years of release (since 1992)

EFI Dexron II

Volume, l

Release models till October, 1994.

Engine of 4.2 l

2.2

Engine of 3.0 l

1.9

All models of release since October, 1994.

1.9

Forward differential

Characteristic

Value

Type of the greasing liquid

SAE 80W/90 GL5

Volume, l

Models Hardtop and Versatile person

5.4

Utiliti's (Van) models and Mini-truck
early years of release

4.3

Utiliti's (Van) models and Mini-truck
late years of release with a suspension bracket on screw springs

5.4

Back differential

Characteristic

Value

Type of the greasing liquid

Differential of usual type and with blocking

SAE 80W/90 GL5

Differential of limited sliding

SAE LS80W/90 GL5 *

Volume, l

Models Hardtop and the Versatile person without blocking of differential

2.1

Models Hardtop and the Versatile person with blocking of differential

3.0

Utiliti's (Van) models and Mini-truck of early years of release

4.7

Utiliti's (Van) models and the Mini-truck of late years of release with a suspension bracket on screw springs

2.1

* At ambient temperature over 40 °C use SAE LS140 GL5 liquid

Brake fluid and hydraulic liquid of coupling

Characteristic

Value

Liquid type

DOT 3

Liquid of system of hydrostrengthening of a wheel

Characteristic

Value

Liquid type

Dexron II

Volume, l

0.9 ÷ 1.0

Lubricant for chassis components

Characteristic

Value

Lubricant type

NLGI#2 on a lithium basis

Requirements imposed to wheels and tires

Standard sizes and pressure of a rating of tires

See information to Schild on the car.

If the tires installed on the car are not listed among admissible on information Schild, consult about the admissible modes of operation and the recommended rating pressure at specialists of dealer office of the company manufacturer of the car.

Engine settings

All models, except 4.2 l of EFI

Characteristic

Value

Ignition order

1-5-3-6-2-4

Type of spark plugs

Engines of 3.0 l

NGK BKR6E

Engines of 4.2 l

NGK BP5ES

Interelectrode candle gap, mm

0.8 ÷ 0.9

Ignition advancing corner at single turns of the engine

Models of 3.0 l

At the disconnected vacuum hose

3 ° ± 2 ° before VMT

At the connected vacuum hose

15 ° ± 5 ° before VMT

Models of 4.2 l at the connected vacuum hose

Models with RKPP

10 ° ± 1 ° before VMT

Models with AT (the selector - in situation D)

10 ° ± 1 ° before VMT

Idling turns, in a minute

Models of 3.0 l

800 ± 50

Models of 4.2 l (the AT selector - in situation D)

650 ± 50

Gap in contacts of the breaker (model of 4.2 l), mm

0.45 ÷ 0.55

Duration (on a corner) the closed condition of contacts of the breaker (model of 4.2 l)

34 ° ÷ 40 °

Resistive resistance of VV of wires, kOhm

not higher than 30

Compression pressure in cylinders, kPa

Standard value

Models of 3.0 l

1 196

Models of 4.2 l

1 177

The minimum admissible

883

The maximum admissible difference between cylinders

98

Gaps of valves, mm

Models of 3.0 l
Zero (hydraulic pushers with the automatic machine chesky compensation are established)

Models of 4.2 l (the engine is heated-up, but is switched off)

0.38

Only models of 4.2 l of EFI

At implementation of adjusting procedures without fail compare the parameters provided below with brought on information Schild of settings of the engine, located in a motive compartment of the car. At a discrepancy correct should be read out the last (from a shilda).

Characteristic

Value

Type of spark plugs

BPR5E

Compression pressure in cylinders, kPa

Standard value

1 187

The minimum admissible

892

The maximum admissible difference between cylinders

98

Engine of 4.2 l

Except the late years of release equipped with injection of fuel (EFI)

General parameters

Characteristic

Value

Engine type

6-cylinder, OHV

Model

TB42

Working volume, cm

3 4 169

Diameter of cylinders, mm

96

Course of pistons, mm

96

Ignition order

1-5-3-6-2-4

Extent of compression

8.3:1

Compression pressure in cylinders, kPa

Standard value

1 177

The minimum admissible

883

The maximum admissible difference between cylinders

98

Head of cylinders

Characteristic

Value

Design

Integral

Material

Aluminum alloy

Admissible not planeness of the interfaced surface, mm

0.2

Height of a head, mm

Standard

117.19 ÷ 117.59

The maximum admissible depth of milling (together with the block), mm

0.2

Width of a working facet of saddles of valves, mm

Inlet

2.4 ÷ 2.8

Final

1.4 ÷ 1.9

Tilt angle of a facet of saddles of valves

45 °

Type of the directing plugs of valves

Replaceable

Height of a vystupaniye of the directing plugs of valves, mm

11.7 ÷ 12.3

Valves and valvate springs

Characteristic

Value

Diameter of cores of valves, mm

Inlet

7.965 ÷ 7.980

Final

7.945 ÷ 7.960

Gap of landing of cores of valves in the directing plugs, mm

Standard

Inlet

0.020 ÷ 0.053

Final

0.040 ÷ 0.073

Limit admissible

0.1

Length of valves, mm

Inlet

116.7 ÷ 117.0

Final

117.0 ÷ 117.3

Height of the cylindrical site (corbel) of plates of valves, mm

Standard

Inlet

1.3

Final

1.5

The minimum admissible

0.5

Tilt angle of a facet of plates of valves

45 ° 30'

Free length of valvate springs, mm

Internal

44.10

External

49.77

Admissible limit of a tortsovka of valvate springs, mm

Internal

1.9

External

2.2

Assembly length of valvate springs, mm

Internal

35

External

40

Assembly of the drive of valves (yokes and axis of yokes)

Characteristic

Value

External Ø of an axis of yokes, mm

19.979 ÷ 20.000

Internal Ø of yokes, mm

20.020 ÷ 20.038

Gap of landing of yokes to axes, mm

0.020 ÷ 0.059

Camshaft

Characteristic

Value

Number of bearings

7

Maximum admissible limit of a bend, mm

0.06

Limit admissible axial side play, mm

0.5

Characteristic	Value
Full length, mm
Station Wagon	4810
Versatile person	Ti 4890
Hardtop	4240
To the utility (Van) (Utility) and Cab Chassis	4970
To the utility (Van) and the Mini-truck of late years of release (since 1992) with a suspension bracket on screw springs	4700
Full width, mm
The versatile person and Hardtop (without slips on wings)	1800
The versatile person and Hardtop (with slips on wings)	1930
To the utility (Van) and Mini-truck	1690
To the utility (Van) and the Mini-truck of late years of release (since 1992) with a suspension bracket on screw springs	1930
Wheel base, mm
Versatile person, Utiliti (Van) and Mini-truck	2970
Hardtop	2400
Radius of turn, m
Versatile person, Utiliti (Van) and Mini-truck	6.7
Hardtop	5.5
Volume of the fuel tank, l
Versatile person and Hardtop	95
To the utility (Van) and Mini-truck	90
The admissible mass of the towed trailer, kg
Models of early years of release (till 1992)
The trailer equipped with brakes	2500
The trailer which is not equipped with brakes	750
Models of late years of release (since 1992)
The trailer equipped with brakes
The versatile person with RKPP	2800
All others	2500
The trailer which is not equipped with brakes	750

*Maximum corner of a forward sves*	42 °
*Maximum corner of a back sves*	30 °
*Maximum corner of a platform*	31 °
*Maximum road gleam, mm*	235
*Maximum admissible depth of a water barrier, mm*	600

Characteristic	Value
Type of the greasing liquid	SAE 20W/50SE is not worse than quality
Volume of the pallet of a case, l
Engine of 4.2 l
With the filter	8.2
Without filter	7.7
Engine of 3.0 l
With the filter	6.4
Without filter	6.0

Characteristic	Value
The volume of cooling liquid (including a broad tank), l
Models of 3.0 l	11.9
Models of 4.2 l with RKPP	13.9
Models of 4.2 l with AT	13.6
Antifreeze type	Antifreeze on the basis of ethylene glycol
Composition of mix, % content of antifreeze
To - 15 °C	30
To - 35 °C	50

Characteristic	Value
Type of the greasing liquid	SAE 75W/90 GL4
Volume, l
Engine of 4.2 l	3.9
Engine of 3.0 l	3.6
Engines of 3.0 l of models of release since October, 1994.	5.1

Characteristic	Value
ATF type	Matic D
Volume, l
Early models	8.5
Models of late years of release (since 1992)	11.8

Characteristic	Value
Ignition order	1-5-3-6-2-4
Type of spark plugs
Engines of 3.0 l	NGK BKR6E
Engines of 4.2 l	NGK BP5ES
Interelectrode candle gap, mm	0.8 ÷ 0.9
Ignition advancing corner at single turns of the engine
Models of 3.0 l
At the disconnected vacuum hose	3 ° ± 2 ° before VMT
At the connected vacuum hose	15 ° ± 5 ° before VMT
Models of 4.2 l at the connected vacuum hose
Models with RKPP	10 ° ± 1 ° before VMT
Models with AT (the selector - in situation D)	10 ° ± 1 ° before VMT
Idling turns, in a minute
Models of 3.0 l	800 ± 50
Models of 4.2 l (the AT selector - in situation D)	650 ± 50
Gap in contacts of the breaker (model of 4.2 l), mm	0.45 ÷ 0.55
Duration (on a corner) the closed condition of contacts of the breaker (model of 4.2 l)	34 ° ÷ 40 °
Resistive resistance of VV of wires, kOhm	not higher than 30
Compression pressure in cylinders, kPa
Standard value
Models of 3.0 l	1 196
Models of 4.2 l	1 177
The minimum admissible	883
The maximum admissible difference between cylinders	98
Gaps of valves, mm
Models of 3.0 l	Zero (hydraulic pushers with the automatic machine chesky compensation are established)
Models of 4.2 l (the engine is heated-up, but is switched off)	0.38

Characteristic	Value
Engine type	6-cylinder, OHV
Model	TB42
Working volume, cm	3 4 169
Diameter of cylinders, mm	96
Course of pistons, mm	96
Ignition order	1-5-3-6-2-4
Extent of compression	8.3:1
Compression pressure in cylinders, kPa
Standard value	1 177
The minimum admissible	883
The maximum admissible difference between cylinders	98

Characteristic	Value
Design	Integral
Material	Aluminum alloy
Admissible not planeness of the interfaced surface, mm	0.2
Height of a head, mm
Standard	117.19 ÷ 117.59
The maximum admissible depth of milling (together with the block), mm	0.2
Width of a working facet of saddles of valves, mm
Inlet	2.4 ÷ 2.8
Final	1.4 ÷ 1.9
Tilt angle of a facet of saddles of valves	45 °
Type of the directing plugs of valves	Replaceable
Height of a vystupaniye of the directing plugs of valves, mm	11.7 ÷ 12.3

Characteristic	Value
Diameter of cores of valves, mm
Inlet	7.965 ÷ 7.980
Final	7.945 ÷ 7.960
Gap of landing of cores of valves in the directing plugs, mm
Standard
Inlet	0.020 ÷ 0.053
Final	0.040 ÷ 0.073
Limit admissible	0.1
Length of valves, mm
Inlet	116.7 ÷ 117.0
Final	117.0 ÷ 117.3
Height of the cylindrical site (corbel) of plates of valves, mm
Standard
Inlet	1.3
Final	1.5
The minimum admissible	0.5
Tilt angle of a facet of plates of valves	45 ° 30'
Free length of valvate springs, mm
Internal	44.10
External	49.77
Admissible limit of a tortsovka of valvate springs, mm
Internal	1.9
External	2.2
Assembly length of valvate springs, mm
Internal	35
External	40

Characteristic	Value
External Ø of an axis of yokes, mm	19.979 ÷ 20.000
Internal Ø of yokes, mm	20.020 ÷ 20.038
Gap of landing of yokes to axes, mm	0.020 ÷ 0.059

Characteristic	Value
Number of bearings	7
Maximum admissible limit of a bend, mm	0.06
Limit admissible axial side play, mm	0.5