13.8. Service of back doors
Removal and installation of the panel of finishing and internal handles
Removal
|
|
- Give the screw of fastening of facing of the handle of the remote drive of the lock to the door panel. Remove facing.
- On models with the manual drive of lowering lifting of door glasses remove the window regulator handle by means of the tool for removal of clamps. In the absence of available this tool hook a facing overlay of the handle the thin strong wire bent on the end in the form of a hook. Lower a hook in a clamp under the driving handle and, having pulled for a wire, take a clamp from a handle end face then remove the handle from a door. Alternatively the handle can be removed by means of the strong matter got under it. For extraction of a clamp it is necessary to pull strongly for fabric corners.
- On models with a separate armrest give fixing screws and remove an armrest from a door.
- On models with power windows with individual switches remove the switch from the panel of finishing of a door and disunite its electric socket. Try not to damage the switch panel.
- With built in an armrest by the switch of a window regulator operate on models as follows:
- Remove a finishing slip from the lower part of the gripping handle of a door and give the screws located under it. The screw-driver with a flat sting carefully hook the gripping handle and remove it from assembly of an armrest.
- The screw-driver with a flat sting carefully hook the panel of the switch of a window regulator and take the last from assembly of an armrest. Disunite the electric socket and take the switch panel aside from a working zone.
- Give screws of fastening of an armrest to the internal panel of a door. Leave an armrest connected to the panel of finishing of a door.
|
|
- Insert the screw-driver with a thin wide flat sting between the panel of finishing and a frame of a door as it is possible closer to one of clamps. Hooking, serially take clamps of fastening of the panel of finishing. Remove the panel from a door (the back door with removed by the panel of finishing and a sealing film is shown on an accompanying illustration).
|
- Carefully remove a polymeric sealing film from the internal panel of a door.
|
|
Installation
Installation is made upside-down.
|
|
- Track correctness of placement on the door panel a polymeric sealing film. Torn or otherwise it is better to replace the damaged film.
- Replace the damaged clamps of the finishing panel.
- Accurately install the finishing panel on a door, serially latching clamps.
- On models with the manual drive of lowering lifting of glasses establish on a door a finishing overlay of the handle of a window regulator, the handle and its clamp. Track that mutual position of the handle and a windowpane corresponded to that on an opposite door.
|
|
|
|
The clamp of the handle of a window regulator has to be installed in the handle before the last is put on a regulator shaft pin. |
Removal and installation of a windowpane and motionless glass of a back door
Removal
Components of door glass and mechanism of its drive
|
|
- Remove internal handles, the panel of finishing of a door and a polymeric sealing film of a door.
- Working through an opening in the door panel, give screws of fastening of a windowpane to the window regulator ram. Carefully lower glass against the stop in a door frame bottom.
- Find clamps of fastening of an internal rubber sealing tape to the top part of a lath of a belt of the internal panel of a door. Grasp at the sealing film near clamps and push it outside, serially releasing clamps. Continue work before full release of a tape from a lath of a door belt. Take a tape aside.
- Find clamps of fastening of an external sealing tape to the top part of the external panel of a door on bottom edge of a window opening. Lift a tape around an arrangement of clamps, serially taking the last before full release of a tape from a door.
- Delay the site of a rubber sealant from the outer edge of a window frame directly over the back directing trench back. Give the screw of fastening of a trench to a transom.
- Give bolts of fastening of the back directing trench to an internal frame of a door.
- Turn the back directing trench on 90 ° and take it from a door at the top.
- By means of the assistant advance motionless glass on a transom. You watch uniformity of distribution of pressing on the top and lower edges of glass. Extract motionless glass together with a sealant from a transom.
- Extract lifting glass from a door. Put it on a soft surface.
|
|
Installation
Installation is made upside-down.
|
|
- Check a condition of a sealant of motionless glass. In case of need make replacement.
- Adjust the provision of the back directing trench, trying to obtain smoothness of lowering lifting of a windowpane.
- Having freely fixed by screws bottom edge of a windowpane on the window regulator ram, lift glass, having densely pressed it to the top back corner of an aperture and to the back directing trench. Having recorded glass in this situation, finally tighten screws.
- Before establishing into place a polymeric sealing film and the panel of finishing of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Removal and installation of the regulator of a window regulator
Removal
|
|
- Remove internal handles of a door, the panel of finishing and a polymeric sealing film.
- Remove a windowpane. Alternatively glass can be recorded in the lifted situation by means of wedges, previously having given screws of fastening it to the window regulator ram.
- On models with electrodriving window regulators disunite the electric socket of the regulator.
- Give bolts of fastening of the regulator to the internal panel of a door. Take assembly of the regulator through an access opening in the internal panel of a door.
|
|
Installation
Installation is made upside-down.
|
|
- Before installation grease the regulator with universal lubricant.
- Adjust the provision of a windowpane.
- Before establishing into place a polymeric sealing film and the panel of finishing of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Removal and installation of the door lock and drive of remote control of it
Removal
Components of the drive of the door lock
|
|
- Remove internal handles of a door, the panel of finishing and a polymeric sealing film.
- Give screws of fastening of the internal handle of the remote drive of the lock of a door to the internal panel of a door.
- Disconnect a rod of the remote drive from the lock. Remove a rod with the handle from a door.
- Disconnect a switching off button rod from the lock.
- On models with the central lock disconnect an executive rod of the driving motor from a latch.
- Give screws of fastening of the mechanism of the lock to a door. Take the lock mechanism from a door through an access opening.
|
|
Installation
Installation is made upside-down.
|
|
- Before installation grease the lock mechanism with universal lubricant.
- Rotating a nut on an executive rod of the external handle of a door, adjust a gap between a nut and the lever of the lock - at the released handle the gap has to make 0.5 ÷ 1.5 mm.
- Before establishing into place a polymeric sealing film and the panel of finishing of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Removal and installation of the external handle of a door
Removal
|
|
- Completely lift a windowpane and remove internal handles of a door, the panel of finishing and a polymeric sealing film.
- Disconnect an executive rod of the lock from the external handle of a door, having released it from a plastic clamp.
- Give nuts of fastening of the handle to the external panel of a door. Remove the handle.
|
|
Installation
Installation is made upside-down.
|
|
- Check a condition of a sealant of the external handle of a door. In case of need replace a sealant.
- In case of need replace a clamp of an executive rod.
- Adjust the provision of a nut of an executive rod of the external handle, trying to obtain a gap between it and the lever of the lock in 0.5 ÷ 1.5 mm (at the released handle).
- Before establishing into place a polymeric sealing film and the panel of finishing of a door, check serviceability of functioning of mechanisms of the lock and a window regulator.
|
|
Replacement and adjustment of a plate of the drummer of the lock
|
|
- Mark with a marker the provision of a plate of the drummer on a door pillar (location of a plate is shown on an accompanying illustration).
- Turn out adjusting screws and remove the drummer's plate. Check a condition of details, defective replace.
- Installation is made upside-down.
- Place the drummer's plate on a rack according to the landing tags put in the course of dismantle. Screw adjusting screws and tighten so that the plate staid put.
- Cover a door, then densely realize it.
- Lift the external handle and carefully open a door, trying not to displace the drummer's plate.
- Tighten screws and again close a door, checking serviceability of functioning of the lock and a plate of the drummer. If there is a need for further adjustment, weaken adjusting screws and displace the drummer's plate in the required direction, trying to obtain trouble-free operation of the lock when opening and closing a door.
- Upon completion of adjustment strongly tighten adjusting screws of a plate.
|
|
